Direct Drive Blower Motor

Motor Vent 115V

Motor Mount Arm

The Rheem Motor Mount Arm is an OEM replacement component designed to securely support and stabilize blower or fan motors within HVAC systems (such as air handlers, furnaces, and condensers). These arms attach the motor housing to the mounting structure, helping maintain proper alignment, reduce vibration, and extend motor life. They’re typically used in Rheem and Ruud HVAC units to replace worn, cracked, or corroded mounting arms, ensuring the motor stays firmly in place during operation. Rheem’s factory motor mount arms are made for precise fit, easy installation, and reliable long-term performance in residential and light commercial systems. Typical Applications: Furnace blower motor support Fan motor mounting in air handlers Replacing damaged or rusted original arms Use in Rheem/Ruud OEM systems

Motor Mount Band Kit

The Lennox 50W89 Motor Mount Band Kit is an OEM replacement accessory used in HVAC systems (air handlers, furnaces, blower units) designed to secure an electric motor to its mounting location. It stabilizes the motor, reduces vibration, helps maintain alignment, and prevents undue stress or wear on connected parts (shafts, bearings, belts, etc.). The band kit is intended to provide a snug, reliable mounting solution that meets the original manufacturer’s specification for fit and performance. In practice, when a motor’s original mount or band becomes weakened, loose, or damaged (due to age, corrosion, fatigue), replacing with the proper motor mount band kit ensures the motor stays in its intended position, reduces rattling or noise, and helps extend the life of the motor and adjacent components.

3/4HP Direct Drive Blower Motor

The ROSTOCK RS8905 is a direct‑drive blower motor intended for HVAC air handler / furnace blower applications. In a direct‑drive setup, the blower wheel (fan) mounts directly on the motor shaft—no belts are used. Key general features: Reversible rotation (CW / CCW) — so it can run in either direction depending on system design. rostockmotors.us +3 Everwell Parts +3 rostockmotors.us +3 Continuous Air Over (AO) — meaning the motor is cooled by ambient or forced airflow over its casing. rostockmotors.us +2 Everwell Parts +2 All-angle mounting — supports multiple orientations. rostockmotors.us +2 Everwell Parts +2 Frame 48 (approx. 5‑5/8″) — a typical HVAC blower motor frame. rostockmotors.us +1 Automatic reset thermal protection — internal protection against overheating, with automatic reset. rostockmotors.us +3 rostockmotors.us +3 Everwell Parts +3 Quiet / efficient design — marketed for higher efficiency and quieter operation. Everwell Parts +1 Not including capacitor — the motor is sold without the run capacitor (you must supply the proper capacitor). rostockmotors.us +1 This motor is intended for duty in furnace / air handler blower compartments where airflow is available for cooling, and it's used when moderate to high airflow is required (e.g. in larger residential systems or light commercial).

1/4HP Direct Drive Blower Motor

The MARS 10583 is a furnace / HVAC blower motor designed for direct drive applications (i.e. the blower wheel or fan is mounted directly on the motor shaft, rather than via belts). It is intended for use in air handlers, furnaces, or HVAC blowers, where moderate airflow is needed under typical duct pressure conditions. Key functional traits: Single‑phase, PSC (permanent split capacitor) motor — common in HVAC blower use. 3-speed windings (i.e. can be wired for low, medium, high speeds) to allow matching blower performance to system load. Reversible rotation, enabling use in systems where airflow direction may be changed or reversed. Open Air Over (OAO) enclosure, meaning the motor is cooled by ambient airflow (air moving over the motor body). All-angle mounting / “all-angle sleeve bearings”, meaning it can be mounted in various orientations (horizontal, vertical, etc.) within reason. Thermal overload protection, built in, to prevent damage under overheating or stall conditions. Uses resilient mounting rings (rubber or vibration-dampening rings) for base mounting to reduce vibration transfer. Compatible with common HVAC mounting patterns, e.g. Rheem mounting holes. Because it's a blower motor built for HVAC, it's designed for continuous duty in “air over” environments (i.e. the blower’s airflow helps cool the motor) rather than being enclosed in a sealed housing without airflow.

Rostock Direct‑Drive Blower Motor RS1973

Reliable 1/2 HP direct‑drive blower motor with reversible rotation (CW/CCW), designed for efficient operation in HVAC systems.

Rostock Direct‑Drive Blower Motor RS1972

A compact and reliable 1/3 HP direct-drive blower motor. Features reversible rotation (CW/CCW), high efficiency, and whisper-quiet operation—ideal for HVAC systems requiring precision airflow.

Rostock Direct‑Drive Blower Motor RS1971

Compact and efficient 1/4 HP direct‑drive blower motor with reversible rotation (CW/CCW), ideal for HVAC applications requiring reliable airflow.

Rostock Direct Drive Blower Motor RS8905

High-efficiency, 3/4 HP direct-drive blower motor with reversible rotation (CW/CCW), designed for reliable airflow in HVAC systems.